Toyota Altezza & Lexus IS200:

Link ECU G4X PlugIn Steuergerät passend für Toyota Altezza & Lexus IS200 3SGE Motor

 

Artikelbeschreibung:

 

220-4000

 

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the 3SGE Beams engine. 

  • Please check your connector matches the header in the listed photo before purchasing.  
  • This ECU works for manual transmissions only.  
  • ECU includes an onboard 4 bar or 7 bar MAP sensor. 
  • Most factory features are supported. 
  • Check the features tab for I/O expansion options 


Suitable applications:  

1998-2001 Toyota Altezza (XE10)  

Lexus IS200 (GXE10)  
G4X PlugIn Key Features (where applicable):

Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

The following expansion connector inputs/outputs are provided: 
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
DI 10                Digital Input for switching functions. 
DI 9                Digital Input for switching functions. 
An Volt 9        Analog 0-5V input 
An Volt 8        Analog 0-5V input 
An Temp 4        Temperature sensor input 
Aux 8                Auxiliary output (2.0 amps maximum when driving to GND. 0.5 amps maximum when driving high.)

1.499,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1

Toyota Chaser, Cresta, Mark II & Soarer:

Link ECU G4X PlugIn Steuergerät passend für Toyota Altezza & Lexus IS200 3SGE Motor

 

Artikelbeschreibung:

 

232-4000

 

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the 1JZ VVTi engine.   

  • Please check your connector matches the header in the listed photo before purchasing.  
  • This ECU works for manual transmissions only.  
  • ECU includes an onboard 4 bar MAP sensor. 
  • Most factory features are supported. 
  • Check the features tab for I/O expansion options 



Suitable applications:  

JZX100 with 1JZ VVTi engine

 

G4X PlugIn Key Features (where applicable):

Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

I/O Expansion Options
The following expansion connector inputs/outputs are provided: 

Expansion Connector 1: (Con5) 
Gnd - Sensor Ground Only  
An Volt 4 
An Temp 2 
+5V Out - Low Current +5V Supply 
An Volt 5 
DI 3 
DI 4 
Aux Inj 8 

Expansion Connector 2: (Con6) 
An Temp 4 
DI 1 
DI 2 
Aux Ign 4 
Aux Ign 5 
Aux Ign 6 
An Volt 1 
An Volt 2

1.899,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1

Link ECU G4X PlugIn Steuergerät passend für Toyota JZX90 Chaser/Cresta/Mark II/JZZ30 Soarer 1JZ-GTE

 

Artikelbeschreibung:

 

235-4000

 

Easy to install. Affordable. Reliable. 

 

G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below.

Designed for the 1JZ-GTE (Non-VVTi) engine.
  • Please check your connector matches the header in the listed photo before purchasing.
  • This ECU works for manual transmissions only.
  • ECU includes an onboard 7 bar MAP sensor.
  • Most factory features are supported. Check the features tab for I/O expansion options
Suitable applications:
  • Toyota JZX90 (Chaser/Cresta/Mark II) with 1JZ-GTE (Non-VVTi) engine, Manual Transmission
  • Toyota JZZ30 (Soarer) with 1JZ-GTE (Non-VVTi) engine, Manual Transmission
Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection. Use the CANJST4 (Link PN 101-0198) cable for connecting CAN devices. This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices. The power supply is protected by a self-resetting fuse rated at 3A continuous.

 

G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

I/O Expansion Options:
The following expansion connector inputs/outputs are provided: 

Expansion Connector 1  (J3)
Pin 1               Ground (signal)
Pin 2                +5v out
Pin 3                Injector 4
Pin 4                Injector 5
Pin 5                Injector 6
Pin 6                AUX 4
Pin 7                AN TEMP 4
Pin 8                AN TEMP 3

Expansion Connector 2 (J9)
Pin 1               Ground (signal)
Pin 2                +5v out
Pin 3                DI7
Pin 4                DI8
Pin 5                DI9
Pin 6                An Volt 8
Pin 7                An Volt 9
Pin 8                An Volt 10

E-Throttle Connector (J5)
Pin 1                Ground (signal)
Pin 2                +5V out
Pin 3                An Volt 4
Pin 4                An Volt 5
Pin 5                An Volt 6
Pin 6                An Volt 7
Pin 7                Aux 10
Pin 8                Aux 9

1.799,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1

Toyota Celica & MR2:

Link ECU G4X PlugIn Steuergerät passend für Toyota Celica ST185 & MR2 SW20 3SGTE

 

Artikelbeschreibung:

 

221-4000

 

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the 3SGTE engine in the models specified below. 

  • Please check your connector matches the header in the listed photo before purchasing.  
  • This ECU works for manual transmissions only.  
  • A Link Air Temp Sensor is highly recommended with this ECU 
  • Most factory features are supported. 
  • Check the features tab for I/O expansion options  


Suitable applications: 

Toyota MR2 (SW20) from 1989 to 1992 

Toyota Celica ST185 (except the Carlos Sainz special edition)

 G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

I/O Expansion Options:
The following expansion connector inputs/outputs are provided: 
Expansion connector:
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
DI 5                Digital Input for switching functions. 
DI 6                Digital Input for switching functions. 
DI 4                Digital Input for switching functions. 
An Volt 4        Analog 0-5V input 
An Volt 5        Analog 0-5V input 
An Volt 6        Analog 0-5V input 

An ignition expansion is provided allowing you to convert to a Direct Spark ignition system. Alternatively, these outputs can be used to drive auxiliary devices. The following pinout describes the available connections. 
Ignition Expansion:
1 Ignition 1 
2 Ignition 2 
3 Ignition 4 
4 Ignition 3

1.499,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1

Link ECU G4X PlugIn Steuergerät passend für Toyota Celica ST205 & MR2 Gen3 3SGTE

 

Artikelbeschreibung:

 

222-4000

 

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 
 
Designed for the 3SGTE engine in the models specified below. 
 
  • Please check your pinoutconnector matches the header in the listed photo before purchasing.  
  • This ECU works for manual transmissions only.  
  • ECU does not fit in the original housing of non-turbo cars 
  • Most factory features are supported. 
  • Check the features tab for I/O expansion options 


Suitable applications: 

Toyota MR2 1993 onwards (Gen3 3SGTE) not including RedTop Beams 

Celica ST205 

 G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

I/O Expansion Options
The following expansion connector inputs/outputs are provided: 
Expansion connector 1 
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
DI 5                Digital Input 
DI 6                Digital Input 
DI 4                Digital Input 
An Volt 7        Analog 0-5V input 
An Volt 5        Analog 0-5V input 
An Volt 6        Analog 0-5V input 

Expansion connector 2 
Ign 5                Ignition 5 Auxiliary Output 
Ign 6                Ignition 6 Auxiliary Output 
Ign 7                Ignition 7 Auxiliary Output 
Ign 8                Ignition 8 Auxiliary Output 
DI 9                Digital Input 
DI 10                Digital Input 
Volt 8                Analog 0-5V input 
Volt 9                Analog 0-5V input

1.499,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1

Toyota GT86:

Link ECU G5 PlugIn Steuergerät passend für Toyota GT86 Scion FRS

 

Artikelbeschreibung:

 

241-4000

 

The GT86 G5 Plug-in is a standalone plug and play replacement for the factory ECU and plugs straight into the original wiring loom, no adapter harness needed and comes with a sample map for a tuning head start. The GT86 G5 Plug-in runs the same powerful microcontroller and firmware as the G5 Voodoo Pro. 


Designed for the 2.0 L 4U-GSE/FA20 H4 Engine. Support for both Manual and Automatic Transmissions. 


Models Supported:

  • Toyota 86, ZN6, 2012 – 2021
  • Toyota GT86, ZN6, 2012-2021
  • Subaru BRZ, ZC6, 2012-2020
  • Scion FR-S 2013-2016

 

For more technical information please see the Features and Specifications tabs.

 

In the box:

  • G5-GT86 Plugin ECU
  • USB-C Connection Cable
  • Locking USB-C extension cable for easy tuning access
  • 2 x M6 screws for ECU mounting in OEM bracket
  • DTM4 CAN Connection Cable (Pre-Installed in Enclosure)
  • Link stickers
  • Control both Direct and Port Injection
  • Full OEM CAN Bus integration
  • Control both Manual and Automatic Transmissions
  • Billet CNC Aluminium Enclosure
  • Mounts in OEM Location
  • Includes a locking USB-C extension cable for easy tuning access
  • Comes with a built-in powered DTM4 CAN cable
  • Full factory E-throttle (DBW) control
  • Full VVT-i control
  • 512MB of Onboard Data Logging, up to 250 channels and 100k samples per second
  • Runs on Link’s renowned PC Link, giving you the confidence to get started right away
  • Backed by Link’s Limited Lifetime Warranty

 

All Link Plug-in ECUs come with the below features as standard:

 

  • Plug and Play - A Direct Replacement for the Factory ECU, no adapter looms needed.
  • All motorsport features enabled – Anti-lag, Boost Control, Cruise Control, Gear Shift Control, Nitrous Control, Launch Control, Paddle Shift Control, Race Timer and Power Management, Rolling Anti-lag and Traction Control
  • Two CAN bus channels
  • Advanced Modelled Fuel equation with flex fuel capability, or a more basic “Traditional” equation is available
  • Exceptional adaptive knock control or traditional threshold-based knock control.
  • Onboard 3 Axis Accelerometer
  • Onboard Trigger Oscilloscope
  • Live user configurable math channels running in ECU
  • Very flexible user configurable CAN bus inputs and outputs. Most 3rd party CAN bus devices supported
  • CAN Keypad control
  • Flexible engine protection limiters
  • PC Link software – Tuning, display and powerful log analysis all in one package.

I/O Options:

 


The following expansion connector inputs/outputs are provided:


Expansion connector 1:
1: +14V Out
2: AUX 15
3: AUX 16
4: DI 11
5: DI 10
6: DI 9 
7: +5V Out
8: GND


Expansion Connector 2:
1: +14V Out
2: Not Connected
3: AN Volt 12
4: AN Volt 11*
5: AN Volt 6*
6: AN Temp 4*
7: +5V Out  
8: GND


*These inputs each have a jumper to either connect them to the Expansion plug or to their normal functions on the main header.

 

2.499,00 €

  • Ausverkauft/Sold Out

Toyota Supra:

Link ECU G4X PlugIn Steuergerät passend für Toyota Supra MK4 2JZ "non VVTI"

 

Artikelbeschreibung:

 

211-4000

 

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the 2JZ non VVTi engine.   

  • Please check your connector matches the header in the listed photo before purchasing.  
  • This ECU works for manual transmissions only.  
  • No onboard MAP sensor. 
  • XS Loom & map sensor highly recommended. 
  • Most factory features are supported. 
  • Check the features tab for I/O expansion options 


Suitable applications:  

Toyota Supra 2JZ non VVTi 

This ECU will support naturally aspirated, parallel twin or single turbo configurations.  Does not support sequential control of the stock twin turbos (note: does not fit case of the NA supra) 

G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
CAN port
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
512 mega bytes data logging memory
Staged injection
Knock with "windowing"

I/O Expansion Options
The Toyota Supra plug-in ECU has two expansion connectors. 
From PCB revision 1.2: 

Expansion Connector 1::  
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
An Volt 7        Analog 0-5V input 
An Volt 6        Analog 0-5V input 
An Temp 4        Temperature sensor input 
An Temp 3        Temperature sensor input 
DI 8                Digital input 
DI 7                Digital input 

Expansion Connector 2  
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
Aux 9                EThrottle - can't be used as an Aux Out 
DI 9                Digital input 
DI 10                Digital input 
An Volt 8        Analog 0-5V input 
An Volt 9        Analog 0-5V input 
An Volt 10        Analog 0-5V input 

1.779,00 €

  • Verfügbar/Available
  • 3 - 5 Tage Lieferzeit1